Smoke Detector for Fire Alarm Systems in Mumbai

Cease Fire & Electrical Services LLP supplies, installs and maintains smoke detectors for building fire alarm systems in Mumbai, including offices, housing societies, hospitals, hotels, factories and warehouses. A smoke detector senses smoke particles and signals the fire alarm panel, usually well before a heat detector would respond, which makes it the main detector for rooms and escape routes. We supply conventional and addressable detectors to suit your panel and test every one before handover.
Types of smoke detector
Optical (photoelectric)
How it worksSmoke scatters or blocks light inside the detector chamber
Where it suitsGeneral use in rooms, corridors and lobbies; responds well to slow, smouldering fires
Multi-sensor
How it worksCombines smoke and heat sensing in one head
Where it suitsAreas where a single sensor may give false alarms
Optical beam
How it worksA light beam spans the space; smoke in its path raises the alarm
Where it suitsLarge, high spaces such as warehouses and atriums
Aspirating (air sampling)
How it worksA fan draws air through sampling pipes to a very sensitive detector
Where it suitsServer rooms, high-value equipment and spaces where point detectors are hard to fit
Ionisation
How it worksUses a small radioactive source
Where it suitsIS 2189 advises against these; multi-sensor detectors are used instead
Conventional detectors report by zone. Addressable detectors report their own address, so the panel shows exactly which detector has operated. A replacement must match your panel's make and protocol.
Where smoke detectors are needed
- IS 2189:2008, the Indian code of practice for fire detection and alarm systems, calls for detectors in:
- Every room or cabin at ceiling level, and under a false ceiling where one is fitted
- The top of stairwells, lift shafts and other shafts, and in lift machine rooms
- Each main landing of an unenclosed staircase
- Cable tunnels, ducts, false floors, AC and AHU rooms and distribution boards
- Kitchens, pantries and boiler rooms usually get heat detectors instead, because steam and cooking fumes can set off a smoke detector.
Spacing and mounting rules to know
- Distance from any point to the nearest detector, flat ceiling up to 7 m high
- Up to 7.5 m
- Ceilings between 7 m and 10 m
- Up to 5 m
- Ceilings above 10 m
- Beam or aspirating detection only
- Minimum number
- At least one smoke detector per 100 m²
- Depth of the sensing element below the ceiling
- 25 mm to 600 mm
- Clearance from walls and beams deeper than 250 mm
- At least 500 mm
- Clearance from supply air diffusers
- At least 1.5 m
IS 11360 is the Indian product standard for smoke detectors. Beams, ceiling height and high air change rates all reduce spacing, so we work out the number from your layout.
Supply, installation and servicing
We supply detectors with their bases, fix and wire them to the approved layout, and test each one before handover. Under our AMC, detectors are cleaned and tested during quarterly checks and the annual service. For replacements, we check your panel make and protocol first so the new detectors work with your system.
Detector faults, a dead battery or a disabled loop on the panel can be reported through FireSense IoT monitoring, which supports the ACMS now required for covered buildings in Maharashtra. See the ACMS guide.

Why choose Cease Fire
Since 1992
A Maharashtra Fire Services Licensed Agency (MFS/
LA/ ) that designs, installs and maintains fire alarm systems.RF-93/ RD-95 Proven on detection work
Addressable fire alarm systems at 65 Adani Electricity substations in Mumbai, and fire detection at Palkhi Roha, a G + 14 building in Kandivali East.
Right part first time
We confirm compatibility with your panel before you order replacement detectors.
Request a quote
Tell us the number of detectors, the area and ceiling height, and your panel make and model if you are adding or replacing detectors. We will confirm the right type and send a quote.
Frequently asked questions
What does a smoke detector do in a fire alarm system?
It senses smoke particles and sends a signal to the fire alarm panel, which sounds the alarm. In most rooms it gives earlier warning than a heat detector.
Which type of smoke detector is best for an office or housing society?
Optical (photoelectric) smoke detectors suit most rooms, corridors and lobbies. Large, high spaces may need beam detectors, and kitchens usually get heat detectors instead.
How many smoke detectors do I need?
IS 2189 allows up to 7.5 m from any point to the nearest detector under a flat ceiling up to 7 m high, with at least one detector per 100 m². Beams, higher ceilings and strong air conditioning increase the number, so we work it out from your layout.
Can I replace a smoke detector on my existing fire alarm panel?
Yes, as long as the new detector matches your panel's make and protocol, especially on addressable systems. Share the panel model and detector part number and we will confirm a compatible replacement.
Why does my smoke detector give false alarms?
Common causes are dust, steam, cooking fumes, insects and detectors placed too close to air conditioning outlets. Cleaning, moving the detector or changing it to a heat or multi-sensor type usually solves the problem.
How often should smoke detectors be cleaned and tested?
IS 2189 says detectors should be cleaned at least every three months and that at least 20% should be tested each year, so every detector is checked within five years. Our AMC covers quarterly checks and an annual service.
Can smoke detector and panel status be monitored remotely?
Yes. FireSense IoT monitoring reports fire alarm panel, detection and battery status to the owner and to us, which supports the ACMS required for covered buildings in Maharashtra.
Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.
Call +91 9920676281







