Engineer testing a red fire alarm control panel in an electrical substation, a long row of grey switchgear cabinets opposite and smoke detectors along the ceiling

Addressable Fire Alarm System in Mumbai

Cease Fire & Electrical Services LLP designs, installs and maintains the addressable fire alarm system for large buildings, hospitals, campuses, industrial plants and utility sites in Mumbai. In an addressable fire alarm system every detector, call point and module has its own address on a loop, so the panel shows the exact device and location that operated. We installed addressable fire alarm systems at 65 Adani Electricity receiving substations across Mumbai between May 2024 and January 2026.

How an addressable system works

The fire alarm panel sends out one or more loops of cable that run through the building and back to the panel. Every device on the loop has a unique address. The panel talks to each device in turn, so it knows which detector or call point is in alarm, which one has a fault and which one has been removed. When the loop is wired to return to the panel (Class A wiring), a single break in the cable does not stop the devices on it from working, and isolators cut off a short circuit so only a small section is lost.

Addressable or conventional?

  1. How devices connect

    On zone circuits

    On loops, each device with its own address

  2. What the panel shows

    The zone in alarm

    The exact device and its location text

  3. Faults

    Shown for the whole zone

    Shown for the exact device

  4. Control of other equipment

    Limited, usually by zone

    Programmed device by device (cause and effect)

  5. Suits

    Smaller buildings with few zones

    Larger or taller buildings, and sites with many services to control

What an addressable system includes

We supply the panels and devices ourselves.

Cause and effect

Because the panel knows exactly which device operated, it can be programmed to act on it. Typical actions are shutting down air handling units on the affected floor, sending lifts to the ground floor, starting stair pressurisation fans, triggering the public address system, and signalling a gas suppression panel. We write the cause and effect with you and your consultant, then test every action at commissioning.

Loop and zone rules in IS 2189

Fire zones per loop
Not more than 8
Isolators
At least two per zone, or a pair for every 20 to 30 detectors and call points
Loop length
Not more than 3,000 m, with wire of at least 1.5 mm²
Loop loading
Not more than 90% of the panel maker's loop capacity
Zone size
Not more than 2,000 m², and one floor per zone if the building is larger than 300 m²
Search distance
Not more than 30 m within a zone

Design standards

We design addressable fire alarm systems to IS 2189 and NFPA 72, and to FM guidelines where the insurer requires them. Detector type and spacing are chosen for each room's height, use and airflow, and loops are planned with spare capacity so the system can grow.

Our process

  1. Free site survey

    We review the building, room uses, other services to be controlled and any existing system.

  2. Design

    Loop and zone layout, device schedule, cause and effect, and cable routes.

  3. Supply and installation

    Panel, devices, modules and loop cabling, installed by our own team.

  4. Testing and commissioning

    Every device tested, panel programmed with location text, cause and effect checked, and staff trained.

  5. Form A

    As a licensed agency, we issue Form A for the work, which you submit to the fire brigade.

  6. AMC and Form B

    Usually quarterly checks with an annual service, and Form B every January and July.

Addressable fire alarm projects

  • Engineer in a hard hat testing an open red fire alarm control panel with a handheld meter, a call point on the wall beside it

    Adani Electricity Mumbai

    Supply, installation, testing and commissioning of addressable fire alarm systems at 65 receiving substations across Mumbai, May 2024 to January 2026, completed within the contract period.

  • Engineer on a scissor lift tightening the clamp of a sway brace on a red sprinkler main under a warehouse roof

    Roquette India, Pantnagar

    Fire alarm systems to FM guidelines, with roof sprinklers and seismic bracing, for four godowns.

See all projects and case studies

Maintenance and Form B

Under AMC we test detectors and call points, check loop faults and isolators, test the outputs in the cause and effect, and check the panel's standby batteries. Detectors in dusty areas are cleaned or replaced before they cause false alarms. A licensed agency must inspect the fire systems and issue Form B every January and July, and we can include this in your AMC.

Why choose Cease Fire

  • Since 1992

    1,500+ projects and the Rashtriya Nirman Ratna Award for Best Government Contractor (2002).

  • Large-scale delivery

    Addressable fire alarms at 65 Adani Electricity substations.

  • Fire and electrical licences

    Maharashtra Fire Services Licensed Agency (MFS/LA/RF-93/RD-95) and Maharashtra Electrical Contractor Licence No. 17545.

  • One team

    Design, panels and devices, installation, programming and AMC from one company.

Book a free site survey

Send your floor plans, building type and the services you want the fire alarm to control. We will survey the site and send a clear proposal.

Frequently asked questions

What is an addressable fire alarm system?

It is a fire alarm system in which every detector, call point and module has its own address on a loop. The panel shows the exact device that operated and where it is.

What is the difference between addressable and conventional fire alarm systems?

A conventional system shows only which zone is in alarm. An addressable system shows the exact device, reports faults device by device and can control other equipment through programmed cause and effect.

When should I choose an addressable system?

Addressable systems suit large or tall buildings, hospitals, campuses and industrial sites, where finding the exact device quickly matters and many services need to be controlled. We recommend the right type after a free site survey.

How many devices can go on one loop?

It depends on the panel maker's loop capacity. IS 2189 recommends loading a loop to no more than 90% of that capacity, with no more than 8 fire zones per loop.

What is an isolator module for?

An isolator cuts off a short circuit on the loop, so only the small section between two isolators is lost and the rest of the loop keeps working.

Can an addressable system control lifts, fans and AHUs?

Yes. Control modules on the loop can shut down AHUs, send lifts to the ground floor and start pressurisation fans when the alarm operates, as programmed in the cause and effect.

Can I upgrade my conventional system to addressable?

Yes. We survey the existing cabling and devices, and propose either a full addressable system or a staged upgrade that keeps some existing detectors on zone modules.

How often should an addressable fire alarm be tested?

Most sites have quarterly checks and an annual service under AMC. A licensed agency must also inspect the system and issue Form B every January and July.

Have you installed addressable systems on large projects?

Yes. We supplied, installed, tested and commissioned addressable fire alarm systems at 65 Adani Electricity receiving substations across Mumbai, from May 2024 to January 2026. See the project page.

Question not answered here? Call our team, Monday to Saturday, 9 am to 7 pm.

Call +91 9920676281